5.24.2009

ferrari 126CK -01

This is the next build, fujimi's 1/20 ferrari 126CK, and it will be a fast WIP because I'll do it curbside.
I started working on the monocoque, the dashboard and the steering wheel.
The seatbelts were build using KA models photoetched set.
The front suspension arms and brakes are built. I also attached the brake wiring to the arms.
I also workedon the engine. It still needs a blackwash to tone down the shine. I will put there some more wiring.
The monocoque and the engine were glued to the floor base.
First test fitting with the tyres. I really like those rain tyres, fujimi did a great job there. The car is looking very nice.
As you can see, the rear suspension arms and the brake ducts are also finished.
And one more test fit with the engine cover. Now I need to work on the wings, the wiring on the engine and polish and painting a final layer of red prior to decalling and clearcoating.

5.10.2009

ferrari 126C2 -11

Finally today I finished the rear wing.
The car is finished!!!!
Next car will be the ferrari 126CK and I will build it curbside.
ferrari 126C2 - 1982
gilles villeneuve
11/feb/2009 - 10/may/2009

4.26.2009

ferrari 126C2 -10

A little progress is done. I attached the slidding skirts to the side of the body.
I painted the nose cone, applied the decals and attached it to the body.
The decalling job is also finished. I also applied two layers of TS-13. I only need to finish the rear wing and the car will be finished.





4.13.2009

ferrari 126C2 -09

I painted the body with italian red. Now I have to sand it and paint a second layer before apply the decals.
As the fujimi kit doesn't provide the engine switch off, I scratchbuilded it.
I attached it to the body. I also used the fire extinger from the 126ck kit and glued the steering in its place.
I glued the roll bar and the rear ventilation ducts. The engine is close to be finished.





ferrari 126C2 -08

I started working on the wheels. As they won't be attached to the car I drilled a hole in the nut.
I masked the rims.

And I painted them with titanium gold.
I used the tyre letters template from the fmd set instead using the decals. It was the first time I used a tyre template and didn't know how it could work.
All went fine and the tyres are finished. I must say that I love more the result of painting the letters than using the decals. The result is absolutely more realistic.

3.30.2009

ferrari 126C2 -07

I made a little progress this weekend. I worked on the radiator pipes. The ones from the kit were short and I had to lenghten them a little bit.
I glued them to the body. I also worked on some more engine parts.


Finally I added some more wiring... tonight I'll try to finish the engine.
And this is the battlefield....




3.22.2009

ferrari 126C2- 06

I started the work on the brake ducts. The parts from the kit are transparent (right on the picture) and I painted them with a very thin coats of buff acrilyc paint (xf-57).
Finally I add some dust and smoke with flat black.
To detail the brakes I bought a Ø3mm threaded bar and cut it in 6mm long pieces. I also bought some nuts and painted them with titanium gold.
Here you can see the brake finished on the right and the brake from the kit on the left. I think I achieved an acceptable detail on it.
I built all brakes in the same way.
The front suspension arms are finished. They only need some blackwashing. I also put some wiring attached on the suspension arms.
Finally I made a test fitting. Now I can work on the engine again.




3.17.2009

ferrari 126C2 -05

The seat was painted with flatblack and I also attached the seatbelts using the p.e. part from fmd set
I also worked on the pedals system. As it won't be visible, I didn't put too much effort in it.
I glued the body parts and put the dashboard, the seat and the gear shift in their place.
I glued the metal panels from the p.e. set on the body.
I also worked on the front suspension arms.
And I also started the job on the brakes.

3.08.2009

ferrari 126C2 -04

I started working on the dashboard. I removed all rims in plastic wich will be replaced for p.e. parts.

I glued the photoetched part and after I painted the whole piece with flatblack.
Once the paint dryed, I lightly sanded the surface of the rims until the metal came on again.
The dashboard is finished. I applied the decals and I used some weldings from an electronic plate to simulate the switches.
I also worked on the engine parts. I rolled up a thin wire to simulate the spring on this engine part.
The engine is going on. Still need some work...

3.02.2009

ferrari 126C2 -03

The hose clamps are on their place. Now they need a little blackwash to tone down their shine.
I started working on the exhausts. I cut and cleaned the pieces to apply some p.e. parts.

Here you can see the original exhaust on the left and the same piece cleaned on the right.
I put the p.e. plates and hose clamps on the exhausts. Finally I painted them with metallic grey, little layers of metallic blue and yellow to simulate some burn parts (the picture can't show it at all)and finally I did a blackwash with flat black.